LT-IS6312XGP-4XS8GT-SD-2BT
The SmartByte LT-IS6312XGP-4XS8GT-SD-2BT is the highly reliable managed industrial PoE++ switch with 8-port 10/100/1000-T PoE and 4-port 1G/2.5G/10GBase-X fiber optical interfaces. It supports IEEE802.3af, IEEE802.3at standard and IEEE802.3bt PoE protocol, the Max power consumption can reach 30W (PoE+) per port, 1-2ports support 90W PoE output. It also supports ERPS redundant network and the self-recovery mechanism is less than 20ms on full load which allows you to scheme a reliable Ethernet network by building a redundant ring topology as your back-up solution. LT-IS6312XGP-4XS8GT-SD-2BT supports DI/DO/RS485, it can work with temperature-humidity sensor to collect environmental data and trigger alarms, which is critical for the industrial application requiring the stable ambient conditions
LT-IS6312XGP-4XS8GT-SD-2BT is the high cost-effective easy-to-use device, which provides essential industrial Ethernet networking function, including wide range power input 44-57VDC, redundant power design with polarity reverse protection, robust IP40 fan-less housing with Din-rail installation, wide operation temperature from -40°C to 75°C as well as high-level EMI/EMC capability. It is the best choice for heavy industrial factory, transportation, oil & gas, chemical, IP Surveillance and processing automation area where environmental conditions are harsh and critical.
➢ 8*10/100/1000Base-T RJ45 PoE, 4*1G/2.5G/10GBase-X SFP+
➢ Redundant power 44-57V input with polarity reverse/over-current protection
➢ Complies with IEEE802.3af PoE, IEEE802.3at PoE+ and IEEE802.3bt standard
➢ Support DI/DO/RS485, work with temperature-humidity sensor to collect environment data and trigger alarms
➢ Support USB one key configuration & upgrading
➢ Layer 3 features: Support IPv4/IPv6 static routing, DHCP server, DHCP relay
➢ Layer 2 features: VLAN/GVRP/QinQ/SPAN/RSPAN/STP, RSTP, MSTP/DHCP/Multicast/ACL
QoS/LLDP/802.1X/AAA/Loop Detect/Dying Gasp/SFP DDM/IPV6 management/Dual Stack
/PoE management/sFlow/Web/SNMP/MQTT/Telnet/TFTP/Web upgrading
➢ Support G.8032 ERPS protocol, recovery time ≤20ms
➢ Support 6KV surge protection and ESD: Air-15kV, Contact-8kV Protection
➢ IP40 fan-less and Din-rail hardware design
➢ Operation temperature: -40 ℃ ~+75℃
LT-IS6312XGP-4XS8GT-SD-2BT | ||||
Interface | Fiber ports | Copper RJ45 ports | ||
4 | 8 | |||
Ethernet | 8*10/100/1000Base-T RJ45 PoE 4*1G/2.5G/10GBase-X SFP+ | |||
CPU | Marvell AC5 series 1.2GHz | |||
Size of RAM | 512MB | |||
Size of Flash | 512MB | |||
Switch chip model | Marvell AC5 series | |||
Management port | 1*RJ45 Console port (115200,8,N,1),1*USB 2.0 | |||
Data & Alarm channel (Removable 8-pin terminal block) | Vout: VO+, VO- | 5V output(0.2A MAX) | ||
1 channel RS485: A, B | Work with temperature-humidity sensor to collect environmental data and trigger alarms | |||
1 channel digital input: DI+,DI- | Status “1”: 12V-30V Status”0”: -30V~3V Max input current: 8 mA | |||
1 channel digital output | Normally open,Normally closed,Pulse 2A@30V DC,0.3A@125V AC | |||
Standard | IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX Ethernet IEEE 802.3ab 1000Base-T Ethernet IEEE 802.3z 1000Base-X Ethernet IEEE 802.3ae 10Gigabit Ethernet IEEE802.3x Flow Control and Back Pressure IEEE 802.1D Spanning Tree Protocol IEEE 802.1w Rapid Spanning Tree Protocol IEEE 802.1Q VLAN ITU-T G.8032 ERPS IEEE 802.1X Port Authentication Network Control IEEE 802.1ab LLDP IEEE 802.3ad LACP IEEE802.3af PoE IEEE802.3at PoE+ IEEE802.3bt PoE++ | |||
LED Indicators | ||||
P (Power indicator) | Off: the device is power off or failed | On: the device power on is normal | ||
S (System status indicator) | Blinking: device initialization | On: device on normal operation | ||
USB (USB status indicator) Green | Off: USB flash drive not insert or not detected by device | |||
On: USB flash drive is detected by device | ||||
Blinking: the device is reading and writing the data from USB flash drive | ||||
Data (RS485 status indicators) | Off: No RS485 data on TX/RX | On: RS485 data on TX/RX | ||
1-8 (Copper ports indicators) Green | Off: ports link down | |||
On: ports link up | ||||
Blinking: data on TX/RX | ||||
1-8 (PoE status indicators) Yellow | Off: PoE not working | |||
On: PoE working | ||||
9-12 (Fiber ports indicators) Green | Off: ports link down | |||
On: ports link up | ||||
Blinking: data on TX/RX | ||||
Power parameter | ||||
Input voltage | 44-57VDC (802.3af) 52-57VDC (802.3at/802.3bt) redundant power input | |||
Input current | 5.8A Max | |||
Power consumption | Full loading without PoE ≤14.5W PoE power budget ≤240W | |||
Connector | Removable 4-pin terminal block | |||
Reverse polarity protection | Support | |||
Over-current protection | Support | |||
Layer 2 switching | ||||
Support GE port aggregation | ||||
Support 2.5GE aggregation | ||||
Support 10GE aggregation | ||||
Support static aggregation | ||||
Support LACP dynamic aggregation | ||||
Up to 64 aggregation groups and up to 8 ports per group | ||||
Port features | Support IEEE802.3x flow control | |||
Support interface counters | ||||
Support port isolation | ||||
Port mirroring (One-to-One, Many-to-One) | ||||
Support loop detection (Port-based; VLAN-based) | ||||
Support broadcast storm suppression (broadcast; unknown multicast; unknown unicast) | ||||
VLAN | IEEE802.1Q tagged VLAN | |||
Mac based VLAN | ||||
IP based VLAN | ||||
Protocol based VLAN | ||||
Voice VLAN, specially divide VLAN for user voice data flow | ||||
Private VLAN, divide a VLAN broadcast domain into multiple subdomains to form a double-layer VLAN structure | ||||
VLAN range: 1-4094 | ||||
Support access mode/trunk mode/hybrid mode | ||||
Mac-address table management | Support static Mac-address management | |||
Support dynamic Mac-address Management | ||||
Support filtering Mac-address | ||||
Support MAC limit based on port and VLAN | ||||
Support MAC flapping based on port and VLAN | ||||
16K Mac-address table size | ||||
GVRP | Normal mode | |||
Fixed mode | ||||
Forbidden mode | ||||
QinQ | Port-based QinQ | |||
VLAN-based QinQ | ||||
VLAN mapping | ||||
Flow-based QinQ | ||||
LLDP | Link Layer Discovery Protocol | |||
Med | ||||
SPAN | Number of Sessions: 7 | |||
Many-to-one | ||||
RSPAN | Remote Switch Port Analyzer | |||
MSTP | 802.1D STP | |||
802.1W RSTP | ||||
802.1S MSTP | ||||
BPDU Guard | ||||
Number of Single Ring Device Connections: 20 | ||||
ERPS G.8032 | Major ring | |||
Sub ring | ||||
Recovery time ≤20ms | ||||
Number of Single Ring Device Connections: No limit | ||||
QoS | QoS Class, Remarking | |||
Support SP, WRR Queue Scheduling | ||||
Ingress Port-based Rate-limit | ||||
Egress Port-based Rate-limit | ||||
Egress port-queue shaper | ||||
Policy-based QoS | ||||
Port Queue Numbers: 8 | ||||
DHCPv4 Snooping | DHCP snooping trust port | |||
DHCP snooping option-82 | ||||
DHCP snooping circuit-id and remote-id customized | ||||
L2 Multicast | ||||
IGMP | IGMP v1, v2, v3 | |||
IGMP Snooping | Internet Group Management Protocol Snooping | |||
Fast Leave | ||||
Multicast Table Size: 1K | ||||
PIM-SM | Protocol Independent Multicast-Sparse Mode | |||
Security features | ||||
ACL | IP Standard ACL IP Extended ACL MAC extend ACL IPv6 ACL Time Range ACL apply on VLAN ACL Entrys, include input and output | |||
802.1x | Port access control Mac-address access control RADIUS server | |||
Port-security | Port-security | |||
IP source guard | IP Source Guard, Port-based IP/Mac Binding Access | |||
ARP-check | Support ARP-check and ARP packet filtering for illegal users | |||
DAI | Dynamic ARP Inspection | |||
Anti-gateway ARP Spoofing | Prevent Gateway ARP Spoofing | |||
Ddos | Ddos attack protection | |||
Access control | Support Telnet/SSH/HTTP/HTTPS user access control | |||
AAA | RADIUS authentication access switch | |||
TACACS authentication access switch | ||||
Authorization | ||||
Reliability | ||||
Loop Detect | Loop detect, based on port or VLAN | |||
EFM | The Ethernet in the first mile, 802.3ah | |||
Management & Maintenance functions | ||||
Dual Stack | IPv4 and IPv6 Dual Stack Management | |||
System Log Management | Syslog Level 7 to 0 Corresponding Debug/Info/Notice/Warning/ Err/ Critical/ Alert | |||
Support connecting up to 3 Servers | ||||
For IPv4 and IPv6 | ||||
User Management | Support password protection, support MD5/SHA256/SHA512 algorithm | |||
Local Management of User Privilege | ||||
Remote authorization by RADIUS or TARCAS | ||||
Enable privilege protection | ||||
User password complexity requirements | ||||
User login fail protection | ||||
User Privilege Level 0 to 15 | ||||
Login Service Management | Up to 8 users online simultaneously | |||
Access control based on IPv4 or IPv6 ACL | ||||
Firmware Management | Firmware upgraded by WEB | |||
Firmware upgraded by CLI | ||||
Dual partition | ||||
Web Management | Web Management | |||
Support HTTP V1.1 | ||||
Support HTTPS | ||||
For IPv4 and IPv6 | ||||
CLI management | Console/Telnet command line management | |||
Fault Detection | Ping/Traceroute, For IPv4 and IPv6 | |||
Dying gasp | ||||
Optical transceiver DDM | ||||
One click fault information collection | ||||
Cable detection | ||||
DNS | Domain Name System | |||
NTP | Network Time Protocol, For IPv4 and IPv6 | |||
Support domain name configuration | ||||
Configuration Import /Export | FTP/TFTP based remote configuration import and export | |||
USB flash drives based local configuration import and export | ||||
sFlow | Sampled flow | |||
SNMP | Version SNMPV2C/V3 | |||
MQTT | Message Queuing Telemetry Transport | |||
RMON | Support RMON (Remote Monitoring) alarm | |||
PoE management | Support 802.3af/802.3at/802.3bt | |||
Support PD watchdog | ||||
Support PoE priority management | ||||
Support Max PoE power configuration for each port | ||||
Support alarm threshold configuration | ||||
Support reserved power configuration | ||||
Support PoE schedule | ||||
Support POE legacy mode | ||||
Dual partition management | Support dual partition switching | |||
Application Protocol Functions | ||||
Telnet server | Support telnet server for IPv4 and IPv6 | |||
Telnet client | Support telnet client for IPv4 and IPv6 | |||
SCP (Secure Copy Protocol) | SCP client/server for IPv4 and IPv6 | |||
SFTP | sftp client/server for IPv4 and IPv6 | |||
SSH server | Support login based on user password-SSH2, support IPv4, IPv6 | |||
Support public key-based login | ||||
TACACS | Support TACACS (the terminal access controller accesses the control system) | |||
TFTP | Support TFTP Client | |||
Layer 3 features | ||||
Static Route | Support VLAN interface and route port | |||
IPv4 static routing table entry configuration | ||||
ARP dynamic learning and static configuration | ||||
IPv6 static routing table entry configuration | ||||
Neighbor discovery and static configuration | ||||
Routing prefix table size 4k for IPv4, for IPv6 divide by 4 | ||||
DHCPv4 Client | Dynamic host configuration protocol for IPv4 | |||
DHCPv6 Client | Dynamic host configuration protocol for IPv6 | |||
DHCPv4 Relay | DHCP Relay for IPv4 | |||
DHCPv4 Server | DHCP Server for IPv4 | |||
Switching features | ||||
Switching capacity | 96Gbps | |||
Packet forwarding rate | 142.8Mpps | |||
MAC address table | 16K | |||
VLAN | 4K | |||
Buffer | 12Mbit | |||
Forwarding delay | <5us | |||
Jumbo Frame | Support 10Kbytes | |||
MDI/MDIX | Support | |||
Watchdog | Support | |||
Mechanical structure | ||||
Case protection | IP40 | |||
Installation method | Din-rail | |||
Dimension(W*D*H)mm | 54*115*158mm | |||
Weight | 1.50 kg | |||
Operating environment | ||||
Operating temperature | -40℃~+75℃ | |||
Storage/transportation temperature | -40℃~+85℃ | |||
Relative humidity | Operation humidity: 10%-90%RH Storage humidity: 5%-95%RH | |||
Industrial Standard | ||||
EMS | Surge protection of power: IEC 61000-4-5 6KV/4KV(8/20us) | |||
Surge protection of Ethernet ports: IEC 61000-4-5 6KV/2KV(10/700us) | ||||
RS:IEC 61000-4-3 80 MHz-1 GHz:10 V/m | ||||
EFT:IEC 61000-4-4 4K/2K | ||||
CS:IEC 61000-4-6 10V | ||||
ESD:IEC 61000-4-2 Contact: 8K;Air: 15K | ||||
EMI | FCC Part 15B Class A | |||
Shock | IEC 60068-2-27 | |||
Free fall | IEC 60068-2-32 | |||
Vibration | IEC 60068-2-6 | |||
Certification | CCC/CE/UKCA/RoHS/REACH/FCC | |||
MTBF | >200,000 hours | |||
Warranty | 5 years | |||
Model | Description |
LT-IS6312XGP-4XS8GT-SD-2BT | L2+ Managed industrial PoE switch with 8*10/100/1000Base-T RJ45 ports(1-2 ports support PoE++ 90W) and 4*1G/2.5G/10GBase-X SFP+ slots, supports DI/DO/RS485 and temperature-humidity sensor on default, complies with IEEE802.3af, IEEE802.3at and IEEE802.3bt standard, DC44-57V input, redundant dual power supply, Din-rail installation; Operation temperature: -40℃~+75℃ |

Copy product links
Long by picture save/share
Related Products
48*1G/10GBase-X slots, 6*40G/50G/100GBase-X slots Marvell-based Data Center Switch
48 *10/100/1000/2500BASE-T Ports, 6* 25G SFP28 Ports
48 *10/100/1000BASE-T Ports, 8* 10G SFP+ Ports
24 *10/100/1000BASE-T Ports, 8* 10G SFP+ Ports
24 *10/100/1000/2500BASE-T Ports, 6* 25G SFP28 Ports
48 *10/100/1000BASE-T RJ45 Ports, 6* 25G SFP28 Ports
48*10/100/1000Base-T + 4*1G/2.5G/10G SFP + Layer 3 Managed PoE Switch
48*10/100/1000Base-T + 4*1G/2.5G/10G SFP + Layer 3 Managed PoE++ Switch
LT-IS6312XGP-4XS8GT-SD-2BT
The SmartByte LT-IS6312XGP-4XS8GT-SD-2BT is the highly reliable managed industrial PoE++ switch with 8-port 10/100/1000-T PoE and 4-port 1G/2.5G/10GBase-X fiber optical interfaces. It supports IEEE802.3af, IEEE802.3at standard and IEEE802.3bt PoE protocol, the Max power consumption can reach 30W (PoE+) per port, 1-2ports support 90W PoE output. It also supports ERPS redundant network and the self-recovery mechanism is less than 20ms on full load which allows you to scheme a reliable Ethernet network by building a redundant ring topology as your back-up solution. LT-IS6312XGP-4XS8GT-SD-2BT supports DI/DO/RS485, it can work with temperature-humidity sensor to collect environmental data and trigger alarms, which is critical for the industrial application requiring the stable ambient conditions
LT-IS6312XGP-4XS8GT-SD-2BT is the high cost-effective easy-to-use device, which provides essential industrial Ethernet networking function, including wide range power input 44-57VDC, redundant power design with polarity reverse protection, robust IP40 fan-less housing with Din-rail installation, wide operation temperature from -40°C to 75°C as well as high-level EMI/EMC capability. It is the best choice for heavy industrial factory, transportation, oil & gas, chemical, IP Surveillance and processing automation area where environmental conditions are harsh and critical.
➢ 8*10/100/1000Base-T RJ45 PoE, 4*1G/2.5G/10GBase-X SFP+
➢ Redundant power 44-57V input with polarity reverse/over-current protection
➢ Complies with IEEE802.3af PoE, IEEE802.3at PoE+ and IEEE802.3bt standard
➢ Support DI/DO/RS485, work with temperature-humidity sensor to collect environment data and trigger alarms
➢ Support USB one key configuration & upgrading
➢ Layer 3 features: Support IPv4/IPv6 static routing, DHCP server, DHCP relay
➢ Layer 2 features: VLAN/GVRP/QinQ/SPAN/RSPAN/STP, RSTP, MSTP/DHCP/Multicast/ACL
QoS/LLDP/802.1X/AAA/Loop Detect/Dying Gasp/SFP DDM/IPV6 management/Dual Stack
/PoE management/sFlow/Web/SNMP/MQTT/Telnet/TFTP/Web upgrading
➢ Support G.8032 ERPS protocol, recovery time ≤20ms
➢ Support 6KV surge protection and ESD: Air-15kV, Contact-8kV Protection
➢ IP40 fan-less and Din-rail hardware design
➢ Operation temperature: -40 ℃ ~+75℃
LT-IS6312XGP-4XS8GT-SD-2BT | ||||
Interface | Fiber ports | Copper RJ45 ports | ||
4 | 8 | |||
Ethernet | 8*10/100/1000Base-T RJ45 PoE 4*1G/2.5G/10GBase-X SFP+ | |||
CPU | Marvell AC5 series 1.2GHz | |||
Size of RAM | 512MB | |||
Size of Flash | 512MB | |||
Switch chip model | Marvell AC5 series | |||
Management port | 1*RJ45 Console port (115200,8,N,1),1*USB 2.0 | |||
Data & Alarm channel (Removable 8-pin terminal block) | Vout: VO+, VO- | 5V output(0.2A MAX) | ||
1 channel RS485: A, B | Work with temperature-humidity sensor to collect environmental data and trigger alarms | |||
1 channel digital input: DI+,DI- | Status “1”: 12V-30V Status”0”: -30V~3V Max input current: 8 mA | |||
1 channel digital output | Normally open,Normally closed,Pulse 2A@30V DC,0.3A@125V AC | |||
Standard | IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX Ethernet IEEE 802.3ab 1000Base-T Ethernet IEEE 802.3z 1000Base-X Ethernet IEEE 802.3ae 10Gigabit Ethernet IEEE802.3x Flow Control and Back Pressure IEEE 802.1D Spanning Tree Protocol IEEE 802.1w Rapid Spanning Tree Protocol IEEE 802.1Q VLAN ITU-T G.8032 ERPS IEEE 802.1X Port Authentication Network Control IEEE 802.1ab LLDP IEEE 802.3ad LACP IEEE802.3af PoE IEEE802.3at PoE+ IEEE802.3bt PoE++ | |||
LED Indicators | ||||
P (Power indicator) | Off: the device is power off or failed | On: the device power on is normal | ||
S (System status indicator) | Blinking: device initialization | On: device on normal operation | ||
USB (USB status indicator) Green | Off: USB flash drive not insert or not detected by device | |||
On: USB flash drive is detected by device | ||||
Blinking: the device is reading and writing the data from USB flash drive | ||||
Data (RS485 status indicators) | Off: No RS485 data on TX/RX | On: RS485 data on TX/RX | ||
1-8 (Copper ports indicators) Green | Off: ports link down | |||
On: ports link up | ||||
Blinking: data on TX/RX | ||||
1-8 (PoE status indicators) Yellow | Off: PoE not working | |||
On: PoE working | ||||
9-12 (Fiber ports indicators) Green | Off: ports link down | |||
On: ports link up | ||||
Blinking: data on TX/RX | ||||
Power parameter | ||||
Input voltage | 44-57VDC (802.3af) 52-57VDC (802.3at/802.3bt) redundant power input | |||
Input current | 5.8A Max | |||
Power consumption | Full loading without PoE ≤14.5W PoE power budget ≤240W | |||
Connector | Removable 4-pin terminal block | |||
Reverse polarity protection | Support | |||
Over-current protection | Support | |||
Layer 2 switching | ||||
Support GE port aggregation | ||||
Support 2.5GE aggregation | ||||
Support 10GE aggregation | ||||
Support static aggregation | ||||
Support LACP dynamic aggregation | ||||
Up to 64 aggregation groups and up to 8 ports per group | ||||
Port features | Support IEEE802.3x flow control | |||
Support interface counters | ||||
Support port isolation | ||||
Port mirroring (One-to-One, Many-to-One) | ||||
Support loop detection (Port-based; VLAN-based) | ||||
Support broadcast storm suppression (broadcast; unknown multicast; unknown unicast) | ||||
VLAN | IEEE802.1Q tagged VLAN | |||
Mac based VLAN | ||||
IP based VLAN | ||||
Protocol based VLAN | ||||
Voice VLAN, specially divide VLAN for user voice data flow | ||||
Private VLAN, divide a VLAN broadcast domain into multiple subdomains to form a double-layer VLAN structure | ||||
VLAN range: 1-4094 | ||||
Support access mode/trunk mode/hybrid mode | ||||
Mac-address table management | Support static Mac-address management | |||
Support dynamic Mac-address Management | ||||
Support filtering Mac-address | ||||
Support MAC limit based on port and VLAN | ||||
Support MAC flapping based on port and VLAN | ||||
16K Mac-address table size | ||||
GVRP | Normal mode | |||
Fixed mode | ||||
Forbidden mode | ||||
QinQ | Port-based QinQ | |||
VLAN-based QinQ | ||||
VLAN mapping | ||||
Flow-based QinQ | ||||
LLDP | Link Layer Discovery Protocol | |||
Med | ||||
SPAN | Number of Sessions: 7 | |||
Many-to-one | ||||
RSPAN | Remote Switch Port Analyzer | |||
MSTP | 802.1D STP | |||
802.1W RSTP | ||||
802.1S MSTP | ||||
BPDU Guard | ||||
Number of Single Ring Device Connections: 20 | ||||
ERPS G.8032 | Major ring | |||
Sub ring | ||||
Recovery time ≤20ms | ||||
Number of Single Ring Device Connections: No limit | ||||
QoS | QoS Class, Remarking | |||
Support SP, WRR Queue Scheduling | ||||
Ingress Port-based Rate-limit | ||||
Egress Port-based Rate-limit | ||||
Egress port-queue shaper | ||||
Policy-based QoS | ||||
Port Queue Numbers: 8 | ||||
DHCPv4 Snooping | DHCP snooping trust port | |||
DHCP snooping option-82 | ||||
DHCP snooping circuit-id and remote-id customized | ||||
L2 Multicast | ||||
IGMP | IGMP v1, v2, v3 | |||
IGMP Snooping | Internet Group Management Protocol Snooping | |||
Fast Leave | ||||
Multicast Table Size: 1K | ||||
PIM-SM | Protocol Independent Multicast-Sparse Mode | |||
Security features | ||||
ACL | IP Standard ACL IP Extended ACL MAC extend ACL IPv6 ACL Time Range ACL apply on VLAN ACL Entrys, include input and output | |||
802.1x | Port access control Mac-address access control RADIUS server | |||
Port-security | Port-security | |||
IP source guard | IP Source Guard, Port-based IP/Mac Binding Access | |||
ARP-check | Support ARP-check and ARP packet filtering for illegal users | |||
DAI | Dynamic ARP Inspection | |||
Anti-gateway ARP Spoofing | Prevent Gateway ARP Spoofing | |||
Ddos | Ddos attack protection | |||
Access control | Support Telnet/SSH/HTTP/HTTPS user access control | |||
AAA | RADIUS authentication access switch | |||
TACACS authentication access switch | ||||
Authorization | ||||
Reliability | ||||
Loop Detect | Loop detect, based on port or VLAN | |||
EFM | The Ethernet in the first mile, 802.3ah | |||
Management & Maintenance functions | ||||
Dual Stack | IPv4 and IPv6 Dual Stack Management | |||
System Log Management | Syslog Level 7 to 0 Corresponding Debug/Info/Notice/Warning/ Err/ Critical/ Alert | |||
Support connecting up to 3 Servers | ||||
For IPv4 and IPv6 | ||||
User Management | Support password protection, support MD5/SHA256/SHA512 algorithm | |||
Local Management of User Privilege | ||||
Remote authorization by RADIUS or TARCAS | ||||
Enable privilege protection | ||||
User password complexity requirements | ||||
User login fail protection | ||||
User Privilege Level 0 to 15 | ||||
Login Service Management | Up to 8 users online simultaneously | |||
Access control based on IPv4 or IPv6 ACL | ||||
Firmware Management | Firmware upgraded by WEB | |||
Firmware upgraded by CLI | ||||
Dual partition | ||||
Web Management | Web Management | |||
Support HTTP V1.1 | ||||
Support HTTPS | ||||
For IPv4 and IPv6 | ||||
CLI management | Console/Telnet command line management | |||
Fault Detection | Ping/Traceroute, For IPv4 and IPv6 | |||
Dying gasp | ||||
Optical transceiver DDM | ||||
One click fault information collection | ||||
Cable detection | ||||
DNS | Domain Name System | |||
NTP | Network Time Protocol, For IPv4 and IPv6 | |||
Support domain name configuration | ||||
Configuration Import /Export | FTP/TFTP based remote configuration import and export | |||
USB flash drives based local configuration import and export | ||||
sFlow | Sampled flow | |||
SNMP | Version SNMPV2C/V3 | |||
MQTT | Message Queuing Telemetry Transport | |||
RMON | Support RMON (Remote Monitoring) alarm | |||
PoE management | Support 802.3af/802.3at/802.3bt | |||
Support PD watchdog | ||||
Support PoE priority management | ||||
Support Max PoE power configuration for each port | ||||
Support alarm threshold configuration | ||||
Support reserved power configuration | ||||
Support PoE schedule | ||||
Support POE legacy mode | ||||
Dual partition management | Support dual partition switching | |||
Application Protocol Functions | ||||
Telnet server | Support telnet server for IPv4 and IPv6 | |||
Telnet client | Support telnet client for IPv4 and IPv6 | |||
SCP (Secure Copy Protocol) | SCP client/server for IPv4 and IPv6 | |||
SFTP | sftp client/server for IPv4 and IPv6 | |||
SSH server | Support login based on user password-SSH2, support IPv4, IPv6 | |||
Support public key-based login | ||||
TACACS | Support TACACS (the terminal access controller accesses the control system) | |||
TFTP | Support TFTP Client | |||
Layer 3 features | ||||
Static Route | Support VLAN interface and route port | |||
IPv4 static routing table entry configuration | ||||
ARP dynamic learning and static configuration | ||||
IPv6 static routing table entry configuration | ||||
Neighbor discovery and static configuration | ||||
Routing prefix table size 4k for IPv4, for IPv6 divide by 4 | ||||
DHCPv4 Client | Dynamic host configuration protocol for IPv4 | |||
DHCPv6 Client | Dynamic host configuration protocol for IPv6 | |||
DHCPv4 Relay | DHCP Relay for IPv4 | |||
DHCPv4 Server | DHCP Server for IPv4 | |||
Switching features | ||||
Switching capacity | 96Gbps | |||
Packet forwarding rate | 142.8Mpps | |||
MAC address table | 16K | |||
VLAN | 4K | |||
Buffer | 12Mbit | |||
Forwarding delay | <5us | |||
Jumbo Frame | Support 10Kbytes | |||
MDI/MDIX | Support | |||
Watchdog | Support | |||
Mechanical structure | ||||
Case protection | IP40 | |||
Installation method | Din-rail | |||
Dimension(W*D*H)mm | 54*115*158mm | |||
Weight | 1.50 kg | |||
Operating environment | ||||
Operating temperature | -40℃~+75℃ | |||
Storage/transportation temperature | -40℃~+85℃ | |||
Relative humidity | Operation humidity: 10%-90%RH Storage humidity: 5%-95%RH | |||
Industrial Standard | ||||
EMS | Surge protection of power: IEC 61000-4-5 6KV/4KV(8/20us) | |||
Surge protection of Ethernet ports: IEC 61000-4-5 6KV/2KV(10/700us) | ||||
RS:IEC 61000-4-3 80 MHz-1 GHz:10 V/m | ||||
EFT:IEC 61000-4-4 4K/2K | ||||
CS:IEC 61000-4-6 10V | ||||
ESD:IEC 61000-4-2 Contact: 8K;Air: 15K | ||||
EMI | FCC Part 15B Class A | |||
Shock | IEC 60068-2-27 | |||
Free fall | IEC 60068-2-32 | |||
Vibration | IEC 60068-2-6 | |||
Certification | CCC/CE/UKCA/RoHS/REACH/FCC | |||
MTBF | >200,000 hours | |||
Warranty | 5 years | |||
Model | Description |
LT-IS6312XGP-4XS8GT-SD-2BT | L2+ Managed industrial PoE switch with 8*10/100/1000Base-T RJ45 ports(1-2 ports support PoE++ 90W) and 4*1G/2.5G/10GBase-X SFP+ slots, supports DI/DO/RS485 and temperature-humidity sensor on default, complies with IEEE802.3af, IEEE802.3at and IEEE802.3bt standard, DC44-57V input, redundant dual power supply, Din-rail installation; Operation temperature: -40℃~+75℃ |

Copy product links
Long by picture save/share
LT-IS6312XGP-4XS8GT-SD-2BT
The SmartByte LT-IS6312XGP-4XS8GT-SD-2BT is the highly reliable managed industrial PoE++ switch with 8-port 10/100/1000-T PoE and 4-port 1G/2.5G/10GBase-X fiber optical interfaces. It supports IEEE802.3af, IEEE802.3at standard and IEEE802.3bt PoE protocol, the Max power consumption can reach 30W (PoE+) per port, 1-2ports support 90W PoE output. It also supports ERPS redundant network and the self-recovery mechanism is less than 20ms on full load which allows you to scheme a reliable Ethernet network by building a redundant ring topology as your back-up solution. LT-IS6312XGP-4XS8GT-SD-2BT supports DI/DO/RS485, it can work with temperature-humidity sensor to collect environmental data and trigger alarms, which is critical for the industrial application requiring the stable ambient conditions
LT-IS6312XGP-4XS8GT-SD-2BT is the high cost-effective easy-to-use device, which provides essential industrial Ethernet networking function, including wide range power input 44-57VDC, redundant power design with polarity reverse protection, robust IP40 fan-less housing with Din-rail installation, wide operation temperature from -40°C to 75°C as well as high-level EMI/EMC capability. It is the best choice for heavy industrial factory, transportation, oil & gas, chemical, IP Surveillance and processing automation area where environmental conditions are harsh and critical.
➢ 8*10/100/1000Base-T RJ45 PoE, 4*1G/2.5G/10GBase-X SFP+
➢ Redundant power 44-57V input with polarity reverse/over-current protection
➢ Complies with IEEE802.3af PoE, IEEE802.3at PoE+ and IEEE802.3bt standard
➢ Support DI/DO/RS485, work with temperature-humidity sensor to collect environment data and trigger alarms
➢ Support USB one key configuration & upgrading
➢ Layer 3 features: Support IPv4/IPv6 static routing, DHCP server, DHCP relay
➢ Layer 2 features: VLAN/GVRP/QinQ/SPAN/RSPAN/STP, RSTP, MSTP/DHCP/Multicast/ACL
QoS/LLDP/802.1X/AAA/Loop Detect/Dying Gasp/SFP DDM/IPV6 management/Dual Stack
/PoE management/sFlow/Web/SNMP/MQTT/Telnet/TFTP/Web upgrading
➢ Support G.8032 ERPS protocol, recovery time ≤20ms
➢ Support 6KV surge protection and ESD: Air-15kV, Contact-8kV Protection
➢ IP40 fan-less and Din-rail hardware design
➢ Operation temperature: -40 ℃ ~+75℃
LT-IS6312XGP-4XS8GT-SD-2BT | ||||
Interface | Fiber ports | Copper RJ45 ports | ||
4 | 8 | |||
Ethernet | 8*10/100/1000Base-T RJ45 PoE 4*1G/2.5G/10GBase-X SFP+ | |||
CPU | Marvell AC5 series 1.2GHz | |||
Size of RAM | 512MB | |||
Size of Flash | 512MB | |||
Switch chip model | Marvell AC5 series | |||
Management port | 1*RJ45 Console port (115200,8,N,1),1*USB 2.0 | |||
Data & Alarm channel (Removable 8-pin terminal block) | Vout: VO+, VO- | 5V output(0.2A MAX) | ||
1 channel RS485: A, B | Work with temperature-humidity sensor to collect environmental data and trigger alarms | |||
1 channel digital input: DI+,DI- | Status “1”: 12V-30V Status”0”: -30V~3V Max input current: 8 mA | |||
1 channel digital output | Normally open,Normally closed,Pulse 2A@30V DC,0.3A@125V AC | |||
Standard | IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX Ethernet IEEE 802.3ab 1000Base-T Ethernet IEEE 802.3z 1000Base-X Ethernet IEEE 802.3ae 10Gigabit Ethernet IEEE802.3x Flow Control and Back Pressure IEEE 802.1D Spanning Tree Protocol IEEE 802.1w Rapid Spanning Tree Protocol IEEE 802.1Q VLAN ITU-T G.8032 ERPS IEEE 802.1X Port Authentication Network Control IEEE 802.1ab LLDP IEEE 802.3ad LACP IEEE802.3af PoE IEEE802.3at PoE+ IEEE802.3bt PoE++ | |||
LED Indicators | ||||
P (Power indicator) | Off: the device is power off or failed | On: the device power on is normal | ||
S (System status indicator) | Blinking: device initialization | On: device on normal operation | ||
USB (USB status indicator) Green | Off: USB flash drive not insert or not detected by device | |||
On: USB flash drive is detected by device | ||||
Blinking: the device is reading and writing the data from USB flash drive | ||||
Data (RS485 status indicators) | Off: No RS485 data on TX/RX | On: RS485 data on TX/RX | ||
1-8 (Copper ports indicators) Green | Off: ports link down | |||
On: ports link up | ||||
Blinking: data on TX/RX | ||||
1-8 (PoE status indicators) Yellow | Off: PoE not working | |||
On: PoE working | ||||
9-12 (Fiber ports indicators) Green | Off: ports link down | |||
On: ports link up | ||||
Blinking: data on TX/RX | ||||
Power parameter | ||||
Input voltage | 44-57VDC (802.3af) 52-57VDC (802.3at/802.3bt) redundant power input | |||
Input current | 5.8A Max | |||
Power consumption | Full loading without PoE ≤14.5W PoE power budget ≤240W | |||
Connector | Removable 4-pin terminal block | |||
Reverse polarity protection | Support | |||
Over-current protection | Support | |||
Layer 2 switching | ||||
Support GE port aggregation | ||||
Support 2.5GE aggregation | ||||
Support 10GE aggregation | ||||
Support static aggregation | ||||
Support LACP dynamic aggregation | ||||
Up to 64 aggregation groups and up to 8 ports per group | ||||
Port features | Support IEEE802.3x flow control | |||
Support interface counters | ||||
Support port isolation | ||||
Port mirroring (One-to-One, Many-to-One) | ||||
Support loop detection (Port-based; VLAN-based) | ||||
Support broadcast storm suppression (broadcast; unknown multicast; unknown unicast) | ||||
VLAN | IEEE802.1Q tagged VLAN | |||
Mac based VLAN | ||||
IP based VLAN | ||||
Protocol based VLAN | ||||
Voice VLAN, specially divide VLAN for user voice data flow | ||||
Private VLAN, divide a VLAN broadcast domain into multiple subdomains to form a double-layer VLAN structure | ||||
VLAN range: 1-4094 | ||||
Support access mode/trunk mode/hybrid mode | ||||
Mac-address table management | Support static Mac-address management | |||
Support dynamic Mac-address Management | ||||
Support filtering Mac-address | ||||
Support MAC limit based on port and VLAN | ||||
Support MAC flapping based on port and VLAN | ||||
16K Mac-address table size | ||||
GVRP | Normal mode | |||
Fixed mode | ||||
Forbidden mode | ||||
QinQ | Port-based QinQ | |||
VLAN-based QinQ | ||||
VLAN mapping | ||||
Flow-based QinQ | ||||
LLDP | Link Layer Discovery Protocol | |||
Med | ||||
SPAN | Number of Sessions: 7 | |||
Many-to-one | ||||
RSPAN | Remote Switch Port Analyzer | |||
MSTP | 802.1D STP | |||
802.1W RSTP | ||||
802.1S MSTP | ||||
BPDU Guard | ||||
Number of Single Ring Device Connections: 20 | ||||
ERPS G.8032 | Major ring | |||
Sub ring | ||||
Recovery time ≤20ms | ||||
Number of Single Ring Device Connections: No limit | ||||
QoS | QoS Class, Remarking | |||
Support SP, WRR Queue Scheduling | ||||
Ingress Port-based Rate-limit | ||||
Egress Port-based Rate-limit | ||||
Egress port-queue shaper | ||||
Policy-based QoS | ||||
Port Queue Numbers: 8 | ||||
DHCPv4 Snooping | DHCP snooping trust port | |||
DHCP snooping option-82 | ||||
DHCP snooping circuit-id and remote-id customized | ||||
L2 Multicast | ||||
IGMP | IGMP v1, v2, v3 | |||
IGMP Snooping | Internet Group Management Protocol Snooping | |||
Fast Leave | ||||
Multicast Table Size: 1K | ||||
PIM-SM | Protocol Independent Multicast-Sparse Mode | |||
Security features | ||||
ACL | IP Standard ACL IP Extended ACL MAC extend ACL IPv6 ACL Time Range ACL apply on VLAN ACL Entrys, include input and output | |||
802.1x | Port access control Mac-address access control RADIUS server | |||
Port-security | Port-security | |||
IP source guard | IP Source Guard, Port-based IP/Mac Binding Access | |||
ARP-check | Support ARP-check and ARP packet filtering for illegal users | |||
DAI | Dynamic ARP Inspection | |||
Anti-gateway ARP Spoofing | Prevent Gateway ARP Spoofing | |||
Ddos | Ddos attack protection | |||
Access control | Support Telnet/SSH/HTTP/HTTPS user access control | |||
AAA | RADIUS authentication access switch | |||
TACACS authentication access switch | ||||
Authorization | ||||
Reliability | ||||
Loop Detect | Loop detect, based on port or VLAN | |||
EFM | The Ethernet in the first mile, 802.3ah | |||
Management & Maintenance functions | ||||
Dual Stack | IPv4 and IPv6 Dual Stack Management | |||
System Log Management | Syslog Level 7 to 0 Corresponding Debug/Info/Notice/Warning/ Err/ Critical/ Alert | |||
Support connecting up to 3 Servers | ||||
For IPv4 and IPv6 | ||||
User Management | Support password protection, support MD5/SHA256/SHA512 algorithm | |||
Local Management of User Privilege | ||||
Remote authorization by RADIUS or TARCAS | ||||
Enable privilege protection | ||||
User password complexity requirements | ||||
User login fail protection | ||||
User Privilege Level 0 to 15 | ||||
Login Service Management | Up to 8 users online simultaneously | |||
Access control based on IPv4 or IPv6 ACL | ||||
Firmware Management | Firmware upgraded by WEB | |||
Firmware upgraded by CLI | ||||
Dual partition | ||||
Web Management | Web Management | |||
Support HTTP V1.1 | ||||
Support HTTPS | ||||
For IPv4 and IPv6 | ||||
CLI management | Console/Telnet command line management | |||
Fault Detection | Ping/Traceroute, For IPv4 and IPv6 | |||
Dying gasp | ||||
Optical transceiver DDM | ||||
One click fault information collection | ||||
Cable detection | ||||
DNS | Domain Name System | |||
NTP | Network Time Protocol, For IPv4 and IPv6 | |||
Support domain name configuration | ||||
Configuration Import /Export | FTP/TFTP based remote configuration import and export | |||
USB flash drives based local configuration import and export | ||||
sFlow | Sampled flow | |||
SNMP | Version SNMPV2C/V3 | |||
MQTT | Message Queuing Telemetry Transport | |||
RMON | Support RMON (Remote Monitoring) alarm | |||
PoE management | Support 802.3af/802.3at/802.3bt | |||
Support PD watchdog | ||||
Support PoE priority management | ||||
Support Max PoE power configuration for each port | ||||
Support alarm threshold configuration | ||||
Support reserved power configuration | ||||
Support PoE schedule | ||||
Support POE legacy mode | ||||
Dual partition management | Support dual partition switching | |||
Application Protocol Functions | ||||
Telnet server | Support telnet server for IPv4 and IPv6 | |||
Telnet client | Support telnet client for IPv4 and IPv6 | |||
SCP (Secure Copy Protocol) | SCP client/server for IPv4 and IPv6 | |||
SFTP | sftp client/server for IPv4 and IPv6 | |||
SSH server | Support login based on user password-SSH2, support IPv4, IPv6 | |||
Support public key-based login | ||||
TACACS | Support TACACS (the terminal access controller accesses the control system) | |||
TFTP | Support TFTP Client | |||
Layer 3 features | ||||
Static Route | Support VLAN interface and route port | |||
IPv4 static routing table entry configuration | ||||
ARP dynamic learning and static configuration | ||||
IPv6 static routing table entry configuration | ||||
Neighbor discovery and static configuration | ||||
Routing prefix table size 4k for IPv4, for IPv6 divide by 4 | ||||
DHCPv4 Client | Dynamic host configuration protocol for IPv4 | |||
DHCPv6 Client | Dynamic host configuration protocol for IPv6 | |||
DHCPv4 Relay | DHCP Relay for IPv4 | |||
DHCPv4 Server | DHCP Server for IPv4 | |||
Switching features | ||||
Switching capacity | 96Gbps | |||
Packet forwarding rate | 142.8Mpps | |||
MAC address table | 16K | |||
VLAN | 4K | |||
Buffer | 12Mbit | |||
Forwarding delay | <5us | |||
Jumbo Frame | Support 10Kbytes | |||
MDI/MDIX | Support | |||
Watchdog | Support | |||
Mechanical structure | ||||
Case protection | IP40 | |||
Installation method | Din-rail | |||
Dimension(W*D*H)mm | 54*115*158mm | |||
Weight | 1.50 kg | |||
Operating environment | ||||
Operating temperature | -40℃~+75℃ | |||
Storage/transportation temperature | -40℃~+85℃ | |||
Relative humidity | Operation humidity: 10%-90%RH Storage humidity: 5%-95%RH | |||
Industrial Standard | ||||
EMS | Surge protection of power: IEC 61000-4-5 6KV/4KV(8/20us) | |||
Surge protection of Ethernet ports: IEC 61000-4-5 6KV/2KV(10/700us) | ||||
RS:IEC 61000-4-3 80 MHz-1 GHz:10 V/m | ||||
EFT:IEC 61000-4-4 4K/2K | ||||
CS:IEC 61000-4-6 10V | ||||
ESD:IEC 61000-4-2 Contact: 8K;Air: 15K | ||||
EMI | FCC Part 15B Class A | |||
Shock | IEC 60068-2-27 | |||
Free fall | IEC 60068-2-32 | |||
Vibration | IEC 60068-2-6 | |||
Certification | CCC/CE/UKCA/RoHS/REACH/FCC | |||
MTBF | >200,000 hours | |||
Warranty | 5 years | |||
Model | Description |
LT-IS6312XGP-4XS8GT-SD-2BT | L2+ Managed industrial PoE switch with 8*10/100/1000Base-T RJ45 ports(1-2 ports support PoE++ 90W) and 4*1G/2.5G/10GBase-X SFP+ slots, supports DI/DO/RS485 and temperature-humidity sensor on default, complies with IEEE802.3af, IEEE802.3at and IEEE802.3bt standard, DC44-57V input, redundant dual power supply, Din-rail installation; Operation temperature: -40℃~+75℃ |

Copy product links
Long by picture save/share

Related Products
48*1G/10GBase-X slots, 6*40G/50G/100GBase-X slots Marvell-based Data Center Switch
48 *10/100/1000/2500BASE-T Ports, 6* 25G SFP28 Ports
48 *10/100/1000BASE-T Ports, 8* 10G SFP+ Ports
24 *10/100/1000BASE-T Ports, 8* 10G SFP+ Ports
24 *10/100/1000/2500BASE-T Ports, 6* 25G SFP28 Ports
48 *10/100/1000BASE-T RJ45 Ports, 6* 25G SFP28 Ports
48*10/100/1000Base-T + 4*1G/2.5G/10G SFP + Layer 3 Managed PoE Switch
48*10/100/1000Base-T + 4*1G/2.5G/10G SFP + Layer 3 Managed PoE++ Switch